ZentriOS Commands

This page lists the ZentriOS Command API with a full description of how to use each command.

There are several interfaces for issuing commands. See Serial Interface, Issuing Commands and Streaming Data. For command format, see Serial Interface, Command Protocol.

ZentriOS Variables, which are used to configure ZentriOS, are accessed using the get and set commands.

The ZentriOS Command API is friendly for humans too. Use the following tips and you'll be an expert ZentriOS terminal jockey in no time flat!

TipDescription
Tab completeType part of a command or variable name then hit the tab key. The command completes or partially completes, just like a terminal in the linux or DOS world.
HistoryUp to 5 commands of history are available. Press the up-arrow key to access recently entered commands.
EditThe left-arrow, home, end and backspace keys may be used to edit or navigate commands already present on the command line.

Shortcuts

A shortcut is assigned to each command. Common sense dictates the rules for shortcuts. Commands that are already short do not need a shortcut other than their name, shortcuts for longer commands sometimes take the first three letters of the command name, and other times take the first letter of the name plus several other letters contained in the name. Shortcuts are no longer than six characters and are easy to guess, the ultimate reference however is command help and the documentation on this page.

Documentation Format

Many of the ZentriOS responses shown in the examples on this page were captured with system.print_level = all, and system.cmd.header_enabled = true. These settings are provided to make it easy for a host microcontroller to parse responses by examining response headers. Information about machine parsing is available in Serial Interface, MCU Config.

Documentation for each command is provided in the format shown below.

command

Abbreviation

cmd

Description

A description of how to use the command with, together with notes about available options and arguments.

Syntax

Formal command syntax with a listing of all available options and arguments.

Example

One or more examples demonstrating how the command is used.

Commands by Group

Description of Commands

adc_take_sample

Abbreviation

adc

Description

Take an analog sample of a pin using an onboard Analog-Digital Converter.

To set the ADC reference voltage, see system.adc.vref.

Syntax

> adc_take_sample <gpio#> [<gain>] [-v]|[-l]/[<LUT Filename.csv>]

Note:

The ADC value can be read in three formats:

Supported Platforms

Example

> adc 1 1
R000007
0x805
> adc 7 1 therm_celsius_lut.csv
R000009
23.4474
> adc 7 -l
R000009
27.5129
> adc 7
R000007
0x78F
> adc 7 -v
R000006
1559

dms

Abbreviation

dms

Description

Perform activities with the DMS, including:

This command requires the device to have access to the Internet, so network credentials wlan.ssid and wlan.passkey must be set. See Getting Started.

Syntax

Claim

dms claim <dms_username> <dms_password>

Claims the current device, associating it with your DMS account.

dms claim <product-code> <activation-token>

Claims the device using an activation token. See DMS Production Workflow, Use an Activation Token. This is a production manufacturing procedure, available for production products only.

Activate

dms activate <product code>

Activates the current device to the specified product.

Update

dms update

The dms update command performs a DMS claim and/or activate operation as well as OTA update. Syntax is:

dms update [-b <bundle version>] <username> <password> [<product code>] / [-b <bundle version>] <product code>

where:

The following command options are supported:

Claim and OTA update the device:

dms update <username> <password>

The device is updated to the device's 'origin product'.

This is similar to using the commands:

> dms claim <username> <password>
> ota

Activate and OTA update the device

dms update <product code>

The device is updated to the activated product.

Note: The device must have been previously claimed.

This is similar to:

> dms activate <product code>
> ota

Claim, activate and OTA update the device

dms update <username> <password> <product code>

The device is claimed, then updated to the activated product.

This is similar to:

> dms claim <username> <password>
> dms activate <product code>
> ota

OTA update the device to the most recent 'release' bundle

dms update

This is the same as:

> ota

OTA update the device to a specific bundle

dms update -b <bundle version>

This is the exact same as:

> ota -b <version>

Note: The device must first be claimed and/or activated. If this operation passes then the device boots into the Kernel to perform the OTA update. This is available only for a development device. See the note for the ota -b option.

Telemetry

dms telemetry

Causes the device to immediately post its telemetry information to the DMS.

Details of the telemetry are set with the following variables:

Supported Platforms

Example

> dms claim my_dms_username my_dms_pw
Success
> dms activate MY_PRODUCTCODE
Success

exit

Abbreviation

exit

Description

Exits command mode immediately and returns to stream mode. Only valid when stream mode is operational.

Syntax

> exit

Supported Platforms

Example

> exit
Command Mode Stop

factory_reset

Abbreviation

fac

Description

Reset the application configuration to factory default values. The WLAN MAC address wlan.mac must be provided as an argument to avoid accidental factory reset.

Note: The application may also be factory reset by asserting GPIO0 for 10 seconds through a module reset as described in Update and Recovery, Factory Reset.

Syntax

> factory_reset <MAC address>

Properties

Supported Platforms

Example

> get wl m
R000019
4C:55:CC:10:03:44
> fac 4C:55:CC:10:03:44
Success

faults_print

Abbreviation

faup

Description

List system faults. After 8 faults, the system enters Safe Mode. See Update and Recovery, Safe Mode.

Syntax

> faults_print

Properties

Supported Platforms

Example

> faup
Success

faults_reset

Abbreviation

faur

Description

Reset system fault counter. See Update and Recovery, Safe Mode.

Syntax

> faults_reset

Properties

Supported Platforms

Example

> faur
Success

file_create

Abbreviation

fcr

Description

Create a new file <size> bytes in length. After the command is issued, the ensuing <size> number of bytes is written to the file system.

Files can be written in chunks smaller than the specified length, using the -o option.

Additional options include a version, file type and CRC, or checksum.

ZentriOS writes the file to extended flash or bulk flash, depending on the --extended or --bulk options. If neither option is specified, ZentriOS writes to bulk flash if available, otherwise to extended flash.

Note: File count and file size may be limited. See File System Limits.

See File System, Writing Files.

Syntax

> file_create [-[e][u][s][y]] [-o] [--extended/--bulk] <filename> <size> [<version> [<type> [<crc>]]]

OptionDescription
-eOptional flag, must be first argument if used. Specifies that the file is essential and must not be deleted during an OTA.
Default: Off
Specified together with -u flag (i.e. -eu for both. Flags can occur in any order).
Note: Files are deleted during OTA only if space is required. OTA may fail if files marked essential leave insufficient space.
-uOptional flag. Set HTTP Server unprotect flag for file.
Default: Off
Specified together with -e flag (i.e. -eu for both. Flags can occur in any order). See HTTP Server Security and Authorization.
-sEncrypt file on creation with the system.security_key. Set the User Encrypted file flag. The system.security_key must be set, or the command fails. See Encryption example below.
-yUsed in conjunction with s: -sy. File contents are pre-encrypted with the system.security_key. Sets the Encrypted and User Encrypted file flags. The system.security_key must be set, or the command fails. For pre-encryption algorithm, see File System, Encrypting Files for Use by ZentriOS.
-oOptional. Leave file open for writing.
Default: Off
If the -o option is not specified, then all the file data must come immediately after the command.
If the -o option is specified, the file can be written in chunks. A stream handle is returned after the command. The write command is used to write data to the file. The stream closes automatically after the specified <size> bytes of data is written. The file is not considered 'valid' until it automatically closes.
If the module is rebooted or the close command is issued before all data is written, the file data is lost. It is not possible to restart writing the file after the stream is manually closed.
See Networking and Security, Network Connections and Streams.
--extendedcreate file on extended flash
--bulkcreate file on bulk flash
filenameName of file to be written.
sizeLength of file in bytes. After the command is issued, write the file content to the serial interface.
versionSpecify version number. Default 1.0.0
typeThe file type, in hex format1. See File System, File Types
Default: FE (MISC_FIX_LEN)
crcoptional, CRC16-CCITT checksum of the file data, in hex format1. See File System, Checksum

1: hex format: upper or lower case, with or without leading 0x, e.g. 0xFE, fe, 0xe1c8

Supported Platforms

Examples

Create a file with no special options

In the example below, the file content , Hello World! is 12 bytes in length and is entered or sent by the user.

> fcr myfile.txt 12
Hello World!
File created

Check result:

> ls -l
!  # Type  Flags  Hnd    Size       Version  Filename
...
#  6 e-FE   0021  104      12       1.0.0.0  myfile.txt

The associated file handle (Hnd) may vary.

Flags 0021: Valid User

Create an unprotected file that can be downloaded even when HTTP Server authorization in force

(see HTTP Server Security and Authorization)

> fcr -u myfile.txt 12
Hello World!
File created

Check result:

> ls -l
!  # Type  Flags  Hnd    Size       Version  Filename
...
#  6 e-FE   0121  104      12       1.0.0.0  myfile.txt

Flags 0121: Valid User Unprotected

Create an essential file that is not deleted during an OTA update

> fcr -e myfile.txt 12
Hello World!
File created

Check result:

> ls -l
!  # Type  Flags  Hnd    Size       Version  Filename
...
#  6 e-FE   0061  104      12       1.0.0.0  myfile.txt

Flags 0061: Valid User Essential

Create a file with specified version and user type

(See File System, File Types)

> fcr myfile.txt 12 1.1.0.1 AB
Hello World!
File created

Check result:

> ls -l
!  # Type  Flags  Hnd    Size       Version  Filename
...
#  6 e-AB   0021  104      12       1.1.0.1  myfile.txt

Create file for writing in chunks

> file_create -o my_file.txt 100
3
> write 3 50
... <50 bytes of data> ...
> write 3 50
... <50 bytes of data> ...
File created

Check result:

!  # Type  Flags  Hnd    Size       Version  Filename
...
#  6 e-FE   0021  107     100       1.0.0.0  my_file.txt

Encryption example

Create file encrypted on creation with system.security_key, which must be pre-set with a user key.

In ls output, note file length is 32 bytes more than data content, and bit 10, User Encrypted flag, is set.

This example also demonstrates opening the file with the security key. See file_open.

> set system.security_key f12ca2a9dae8bdb48d959e65ec54f6da
User key set
Set OK
> file_create -s my_file.txt 100
Here is a test file encrypted with system.security_key
using the file_create -s option. Note flags
File created
> ls -l
!  # Type  Flags  Hnd    Size       Version  Filename
...
#  6 e-FE   0421   97     132       1.0.0.0  my_file.txt
...
file_open my_file.txt
[Opened: 0]
0
> read 0 100
J¡@õk_WRA7WFJÙSG...(without key, output is not decrypted)
> file_open my_file.txt f12ca2a9dae8bdb48d959e65ec54f6da
[Opened: 1]
1
> read 1 100
Here is a test file encrypted with system.security_key
using the file_create -s option. Note flags
[Closed: 1]

file_delete

Abbreviation

fde

Description

Delete a file from the file system.

Syntax

> file_delete <filename> | <memory>-<handle> where

Note: <memory>-<handle> overrides <filename> - for example, if there exist both a file in extended flash with file handle 234, and a file named e-234, then the command file_delete e-234 deletes the file with memory-handle e-234, rather than the file named e-234.

Properties

Supported Platforms

Example

> fde myfile.txt
L000014
File deleted
R000009
Success

Example

To delete the file with handle 234 on extended flash:

> file_delete e-234
L000014
File deleted
R000009
Success

file_open

Abbreviation

fop

Description

Open a file and return a file stream handle if successful. Once open, the file contents may be read with the stream_read command.

See Networking and Security, Network Connections and Streams.

Syntax

> file_open <filename> | <memory>-<handle> [<security key>]

where:

Note: <memory>-<handle> overrides <filename> - for example, if there exist both a file in extended flash with file handle 234, and a file named e-234, then the command file_open e-234 opens the file with memory-handle e-234, rather than the file named e-234.

Supported Platforms

Example

> fop myfile.txt
R000003
0

Example

To open the file with handle 234 on extended flash:

> file_open e-234
R000003
0

file_stat

Abbreviation

fst

Description

Display file statistics for the specified file.

Statistics are displayed in a comma separated list, in the order:

size,CRC,long version,storage type,file type,flags,handle

#StatCommentReference
1sizefile size, displayed in decimal format
2CRCCRC is calculated from the unencrypted file data. Displayed in hex format, with no 0x prefix.File System, File Checksum
3long versionFile System, File Version
4storage type
  • i - MCU internal flash
  • e - extended flash
  • b - bulk serial flash
File System, Flash Storage
5file typeFile System, File Types
6flagsFile System, File Flags
7handleListed in the 'Hnd' column in ls -l outputA unique ID assigned to each file

The ls -v (verbose file listing) command displays all of these properties except the CRC.

Syntax

> file_stat <filename>/<memory type>-<handle> where:

Supported Platforms

Example

> file_stat geotrust_ca.pem
1236,6E5A,3.0.0.11,e,3,1,8
> file_stat e-8
1236,6E5A,3.0.0.11,e,3,1,8

force_safemode

Abbreviation

force_safemode

Description

Force the module into safe mode. This command is used by a host to test recovery procedures if the module enters safe mode. See Application Notes, Recovery from Safe Mode for further information.

This is a hidden command that does not appear in the list of commands returned by help commands.

Syntax

> force_safemode <module MAC address>

Supported Platforms

Example

> force_safemode 4C:55:CC:10:10:98
Forcing safemode...
Rebooting
[Disassociated]
ZentriOS-2.1.0.9, Built:2015-01-25 15:58:14 for AMW004.3, Board:AMW004-E03.3

*** Max faults exceeded. Entering Safe Mode.
SAFEMODE>

format_flash

Abbreviation

format

Description

Format (i.e. erase all contents) of bulk or extended flash chip. If the extended flash is specified, ALL files BUT the wifi_fw.bin file are erased.

For details on enabling and using bulk flash, see File System, Flash Storage. See also the system.bflash.cs_gpio variable.

Syntax

> format_flash <bulk/extended> <module MAC address>

Properties

Supported Platforms

Example

> format bulk 4C:55:CC:10:10:98
Formatting flash...

get

Abbreviation

get

Description

Get the value of a ZentriOS variable or group of variables.

Syntax

> get <[variable name] / [variable group]> [options]

Properties

Supported Platforms

Example 1

> get time.rtc utc
R000029
2014-03-23T23:54:33.021464Z

Example 2

> get bus
R000166
bus.data_bus: uart0
bus.log_bus: uart0
bus.mode: command
bus.stream.cmd_gpio: 0
bus.stream.cmd_seq: $$$
bus.stream.flush_count: 1500
bus.stream.flush_time: 20

gpio_dir

Abbreviation

gdi

Description

Set the direction of a general purpose I/O pin. To deregister the GPIO, set the direction to either -1 or none.

Note : This is a run-time only setting: the value is not saved with the save command. To set the direction of a GPIO after a reboot, set the variable gpio_init. See Peripherals, Setting GPIO Function.

Syntax

> gpio_dir <GPIO#> <direction name/enum> [0/1]

where:

For each I/O type there is a name and ab enum values. The <direction name/enum> argument can specify either a name or an enum value:

I/O Type DescriptionDirection NameEnum Value
Input, pull-upipu0
Input, pull-downipd1
Input, high-impedancein2
Output, push-pullout3
Output, open-drain no-pullood4
Output, open-drain pull-upoodpu5
Deregister the GPIOnone-1

Supported Platforms

Example

> gdi 12 in
R000008
Set OK

gpio_get

Abbreviation

gge

Description

Get the current value of a general purpose I/O pin.

Syntax

> gpio_get <GPIO#>

Supported Platforms

Example

> gge 12
R000003
0

gpio_set

Abbreviation

gse

Description

Immediately set the value of a general purpose I/O pin. When setting a GPIO, the GPIO direction must be also correctly set using the command gpio_dir or the command will fail.

Syntax

> gpio_set <GPIO#> <value>

Supported Platforms

Example

> gse 12 1
L000032
GPIO not configured for output
R100016
Command failed

gpios_dir

Abbreviation

gdis

Description

Set the direction of all general purpose I/O pins. A direction for all GPIOs must be provided with the direction of GPIO 0 in the first (left-most) position in the array.

Note : This is a run-time only setting: the direction values are not saved with the save command. To set the direction of a GPIO after a reboot, set the variable gpio_init. See Peripherals, Setting GPIO Function.

Syntax

> gpios_dir <direction array> where a <direction array> element may be one of the values in the following table.

EnumeratorI/O Type Description
0Input, with pull-up
1Input, pull-down
2Input, high-impedance
3Output, push-pull
4Output, open-drain no-pull
5Output, open-drain pull-up
6Deregister the GPIO

Supported Platforms

Example

> gdis 10011011333530011000222226622
R000008
Set OK

gpios_get

Abbreviation

gges

Description

Get the current value of all general purpose I/O pins.

The value of standard GPIOs is returned as either 0 or 1. Other GPIO types not configured for GPIO access (such as UART pins or system indicators) are returned as X. GPIO values are in GPIO number order, increasing from left to right, with value for GPIO0 at left.

Syntax

> gpios_get

Supported Platforms

Example

> gpios_get
R000031
0XX00X0000000XX10XXX000000000

gpios_set

Abbreviation

gses

Description

Immediately set the value of all general purpose I/O pins. When setting a GPIO, the GPIO direction must be also correctly set using gpio_dir or gpios_dir or the command will fail. The value for all GPIOs must be provided, with the value of GPIO 0 in the first (left-most) position in the array.

Syntax

> gpios_set <GPIO value array>

Supported Platforms

Example

The examples shown below are for the AMW004 Wallaby module which has 29 GPIOs, the first example command failed because the GPIO value array contained less than 29 values.

> gses 100110100101101001001011
L000022
Must supply 29 gpios
R700018
Invalid argument

> gses 10011011001011110100100101111
R000008
Set OK

help

Abbreviation

help, ?

Description

Return a list of commands or variables; or return help for a specific command or variable.

Syntax

> help [all/commands/variables/<command>/<variable>]

Supported Platforms

Example

> help
Usage   : help [all/commands/variables/<command>/<variable>]
Shortcut: help
Brief   : Return a list of commands or variables; or return
          help for a specific command, variable or group of
          variables.

http_add_header

Abbreviation

had

Description

Add a custom HTTP header to the HTTP stream specified by <handle>.

See Networking and Security, HTTP Client.

This command requires an open request stream, resulting from issuing either http_get, http_head or http_post with the -o option.

To complete and send the open request after adding headers, issue http_read_status <handle>.

Syntax

> http_add_header <handle> <key>[:extended] <value> where:

OptionDescription
<handle>the stream handle supplied in response to the http_get, http_head or http_post commands (opened with -o option)
<key>header key
<key:>extendedIf the <key> argument has :extended appended to it (no spaces) then the <value> argument is omitted and the following line after the command is the value of the HTTP header. The extended HTTP header value may be up to 1024 characters. The extended HTTP header value is terminated with the \r\n characters.
<value>header value (if <key>:extended not used).

Options must be provided in the order shown.

Supported Platforms

Example

> http_get -o example.com
[2018-09-04 | 02:49:19: Opening: example.com]
Request GET /
Connecting (http): example.com:80
[2018-09-04 | 02:49:19: Opened: 0]
0
> http_add_header 0 Accept text/html
Success
> http_read_status 0
Request GET /
Connecting (http): example.com:80
200
> read 0 1000
<!doctype html><html...

http_download

Abbreviation

hdo

Description

Download one or more files from a remote HTTP server and save to the extended or bulk flash.

Timeout is determined by tcp.client.connect_timeout.

Note: The remote HTTP server must return the Content-length header in the HTTP response. The file system must have the size of the file before creating it.

Note: File count and file size are limited. See File System Limits.

See Networking and Security, TLS Errors for details of the error response to TLS failure.

See Networking and Security, HTTP Client.

Syntax

Download a Single File

> http_download [-i <wlan/softap>] [-m <json_size>] [-d] [-[e][u][s][y]] [-c <CRC>] <url>
  [<flash_file_name> [<version> [<type> [<cert_filename>  ] ] ] ]

where parameters are as follows:

OptionDescription
-iOptional - Specify interface, MUST come first. If omitted uses network.default_interface.
-m <json_size>Optional - Download multiple files with a json specification of size <json_size>.
MUST come first if -i option not used.
No other parameters are valid with -m option.
See Downloading Multiple Files below for more information.
-dDon't delete duplicate files.
By default all duplicate file names are overwritten; with this option the command will fail on duplicates.
-eOptional flag - Indicates file is essential. Specified together with -u flag (i.e. -eu for both. Flags can appear in any order).
-uOptional flag - Set HTTP Server unprotected flag for file. Specified together with -e flag (i.e. -eu for both. Flags can appear in any order). See HTTP Server Security and Authorization.
-sEncrypt file on creation with the system.security_key. Set the User Encrypted file flag.
-yUsed in conjunction with s: -sy. File contents are pre-encrypted with the system.security_key. Set the Encrypted and User Encrypted file flags. The system.security_key must be set, or the command fails. See also File System, Encrypting Files for Use by ZentriOS.
-c <CRC>Optional, CRC for file, in hex format*. On download, the file CRC is calculated and compared against this value. The file is not set 'valid' unless the CRCs match. See File System, File Checksum.
<url>Full path to a file on a http server. See below for more info about URL.
<flash_file_name>Optional - name to save file as. Use url filename if omitted
<version>Optional - default 1.0.0 if omitted, set to 0 to use default
<type>Optional - the type of file, default: miscellaneous text file, 0xFE. Type can be in hex or decimal format. See File System, File Types
<cert_filename>Optional - TLS certificate filename

Downloading Multiple Files > http_download -m <json_size>

Immediately after issuing this command, send <json size> bytes of a JSON formatted manifest file. An example of the manifest file is as follows:

{
   "path"  : "https://myserver.com/path/to/my/files/",
   "cert"  : "mycert.pem",
   "files" : [
                {
                    "remote"  : "name_of_remote_file.html",
                    "local"   : "name_of_flash_file.html",
                    "version" : "1.0.0",
                    "type"    : 150,
                    "flags"   : "eu",
                    "crc"     : 23423
                },
                { ... }
              ]
}

Notes:

String Replacement

ZentriOS allows string replacement in the URL of the file for download, using a C-like or pythonesque syntax.

If the url contains %s, then the supplied filename is substituted for %s.

Example: hdo 192.168.1.110:50007?id=%s&action=download my_file.txt generates the URL: http://192.168.1.110:50007?id=my_file.txt&action=download and creates the file: my_file.txt in the module file system.

String replacement is also available in the manifest. For example:

{
   "path" : "http://myserver.com?file=%s&user=name&pass=1234",
   "cert" : "mycert.pem",
   "files" : [
                {
                    "remote" : "my_file1.txt",
                },
                {
                    "remote" : "my_file2.txt",
                },
              ]
}

generates the following URLs for download:

http://myserver.com?file=my_file1.txt&user=name&pass=1234
http://myserver.com?file=my_file2.txt&user=name&pass=1234

Supported Platforms

Example

Save page at example.com to file test.html:

> hdo http://example.com test.html
Downloading: test.html to flash file system
Request GET /
Connecting (http): example.com:80
HTTP response: 200
Success
> ls -v
!  # Type  Flags  Hnd    Size    Version  Filename
...
#  8 e-FE   0021  108    1270       1.0.0.0  test.html
...

http_get

Abbreviation

hge

Description

Perform an HTTP(S) GET request and return a network stream handle if successful.

The protocol is assumed to be HTTP unless otherwise specified in the <url> parameter.

For a URL longer than 124 characters the command and url exceed the maximum command line length.

In this case use the --long_url option instead of including the URL as a command argument. Send the long URL, terminated by \r\n, immediately after the terminating \r\n of the command.

To allow custom headers, use the -o option to leave the request open. To complete and send the open request after adding headers, issue http_read_status <handle>.

Timeout is determined by tcp.client.connect_timeout.

See Networking and Security, TLS Errors for details of the error response to TLS failure.

See:

Syntax

> http_get [-i <wlan/softap>] [-g < GPIO#>] [-o] <url> / --long_url [ca_cert_filename]

where:

ParameterDescription
-iNetwork interface. Possible values are wlan or softap. Overrides default specified by network.default_interface
-g <GPIO#>specify a GPIO to indicate buffered data is waiting to be read. Set to -1 to disable
-oOpen the HTTP request but do not send. This enables custom header(s) to be added to the request using the http_add_header command.
<url>URL to which request is sent. The URL prefix http:// is optional for standard HTTP transactions, however https:* must be added for secure HTTPS transactions.
--long_urlIf --long_url is given instead of <url>, then immediately following the http_get command should be the URL string, e.g
http_get --long_url\r\n
http://example.com?param1=abvcedfgssassssdfs&param2=asdfadsfasd&param3=11111111111111\r\n
[ca_cert_filename]CA certificate file. Overrides default specified by network.tls.ca_cert

Options must be provided in the order shown.

Supported Platforms

Example

> hge https://www.google.com.au
[2014-04-02 | 13:27:20: Connecting: https://www.google.com.au]
Request GET /
Connecting (HTTP): www.google.com.au:443
Starting TLS
[2014-04-02 | 13:27:21: Connected: 0]
HTTP response: 200
Status: 200
0

> hge -o example.com:80
[2014-04-11 | 10:48:25: Opening: example.com:80]
Request GET /
Connecting (HTTP): example.com:80
[2014-04-11 | 10:48:25: Opened: 1]
1

> http_get --long_url
http://example.com/arbitrary_page?param1=abvcedfgssassssdfs&param2=asdfadsfasd&param3=11111111111111
[2016-05-10 | 02:26:50: Opening:http://example.com]
Request GET /arbitrary_page?param1=abvcedfgssassssdfs&param2=asdfadsfasd&param3=11111111111111
Connecting (http): example.com:80
[2016-05-10 | 02:26:50: Opened: 2]
Status: 200
2

http_head

Abbreviation

hhe

Description

Perform an HTTP(S) HEAD request and return a network stream handle if successful.

The protocol is assumed to be HTTP unless otherwise specified in the <url> parameter.

To allow custom headers, use the -o option to leave the request open. To complete and send the open request after adding headers, issue http_read_status <handle>.

Timeout is determined by tcp.client.connect_timeout.

See:

Syntax

> http_head [-i <wlan/softap>] -o <url> [ca_cert_filename] where:

ParameterDescription
-iNetwork interface. Possible values are wlan or softap. Overrides default specified by network.default_interface
-oOpen the HTTP request but do not send. This enables custom header(s) to be added to the request using the http_add_header command.
<url>URL to which request is sent. The URL prefix http:// is optional for standard HTTP transactions, however https:* must be added for secure HTTPS transactions.
[ca_cert_filename]CA certificate file. Overrides default specified by network.ca_cert

Options must be provided in the order shown.

Supported Platforms

Example

> hhe example.com
[2014-04-02 | 13:32:28: Connecting: example.com]
Request HEAD /
Connecting (HTTP): example.com:80
[2014-04-02 | 13:32:29: Connected: 0]
HTTP response: 200
Status: 200
0

http_post

Abbreviation

hpo

Description

Perform an HTTP(S) POST request and return a network stream handle if successful.

The protocol is assumed to be HTTP unless otherwise specified in the <url> parameter.

To allow custom headers, use the -o option to leave the request open. To complete and send the open request after adding headers, issue http_read_status <handle>.

The HTTP Content-type must be provided.

Timeout is determined by tcp.client.connect_timeout.

See:

Syntax

> http_post [-i <wlan/softap>] [-g < GPIO#>] [-o] [-l <content-length>] <url> / --long_url<url> <content type> [ca_cert_filename] where:

ParameterDescription
-iNetwork interface. Possible values are wlan or softap. Overrides default specified by network.default_interface
-g <GPIO#>specify a GPIO to indicate buffered data is waiting to be read. Set to -1 to disable
-oOpen the HTTP request but do not send. This enables custom header(s) to be added to the request using the http_add_header command.
-l <content-length>This replaces the default HTTP header Transfer-Encoding : chunked with the header Content-Length: XXX where XXX is the specified content_length.
By default an HTTP request is sent with chunked encoding. If this option is specified then chunked encoding is not used. This may be necessary for HTTP servers that do not support chunked encoding. After issuing the command, the write command must be used to write <content-length> bytes of data.
Note: If the -l option is specified then the connection will be left open, thus the -o option is not needed.
<url>URL to which request is sent. The URL prefix http:// is optional for standard HTTP transactions, however https:* must be added for secure HTTPS transactions.
--long_url <url>allows an aribitrary length URL string, with a maximum length of 1023 characters. The URL string follows the http_post command on the next line
<content_type>The Content-type, (Internet media type, MIME type), of the content to be posted (e.g. application/json).
[ca_cert_filename]CA certificate file. Overrides default specified by network.tls.ca_cert

Options must be provided in the order shown.

Supported Platforms

Example

> hpo http://example.com application/json
[2014-04-02 | 13:35:19: Connecting: http://example.com]
Request POST /
Connecting (HTTP): example.com:80
[2014-04-02 | 13:35:20: Connected: 0]
HTTP response: 411
Status: 411
0
> hpo -o example.com:80 application/json
[2014-04-11 | 10:45:50: Opening: example.com:80]
Request POST /
Connecting (HTTP): example.com:80
[2014-04-11 | 10:45:50: Opened: 1]
1

http_read_status

Abbreviation

hre

Description

Read the HTTP response code returned by the last HTTP transaction on the stream specified by <handle>.

If the HTTP request is pending and the transaction is incomplete, http_read_status sends the request and forces completion. An HTTP request is pending, or open, when it results from issuing either http_get, http_head or http_post with the -o option. This allows adding custom headers with the http_add_header command.

See Networking and Security, HTTP Client.

Syntax

> http_read_status <handle>

Supported Platforms

Example

> hre 1
411

http_upload

Abbreviation

hup

Description

Upload file(s) from the device flash to a remote HTTP server using HTTP POST and file upload.

Timeout is determined by tcp.client.connect_timeout.

See:

Syntax

Upload a Single File

> http_upload [-i <softap/wlan>]  [-k <security key>] <url>  <local filename>
  [<remote filename> [<content type> [<cert filename>]]]

where:

Upload Multiple Files using JSON Manifest > http_upload [-i <softap/wlan>] -m <json size> where:

The manifest must be input directly after the command is issued. Manifest format:

{
  "path" : "https://myserver.com/path/to/save/files",
  "cert" : "mycert.pem",
  "files" : [ {
    "local"  : "my_file_to_load.txt",
    "remote" : "file_name_on_server.txt",
    "name"   : "file",
    "type"   : "application/octet-stream",
    },
    { ... }
  ]
}

The manifest cannot contain javascript style commments.

If provided, the cert must be the name of an existing file in the device sflash.

The following optional properties are given the specified default values only if the properties are completely omitted from the manifest. Leaving them blank results in blank values, not default values.

PropertyDescriptionDefault
remoteName of file on remote systemlocal value - the name of the file on the module file system.
nameAppears in the form-data "name" field"file"
typeMime-type of file content"application/octet-stream"

For examples, see the http_upload application note.

Supported Platforms

Example

> hup http://myserver.com/uploadpage ghm_capabilities.json testfile.json
Uploading: ghm_capabilities.json to server
Request POST /uploadpage
Connecting (http): myserver.com:80
HTTP response: 200
Success

The file is saved on the upload server at myserver.com:80 as testfile.json

i2c_master_config

Abbreviation

i2cmc

Description

Configure an I2C slave peripheral such as an accelerometer, humidity sensor, light sensor, etc.

Notes:

See Networking and Security, Network Connections and Streams.

Syntax

> i2c_master_config <slave hex address> <clock rate> [<retries> [<config bitmask>]]

where:

<config bitmask> is a bitmask specifying the various flags for the I2C slave. The bits have the following meanings:

Bit #NameDescription
0HexifyWhen set, input data to the stream_write command is converted from a hex string to binary.
Output data from the stream_read command is converted from binary to a hex string.
Note: When this flag is set, up to <rx buffer>/2 -1 bytes may be read at a time

Supported Platforms

Example

> i2c_master_config 0x19 standard 0 0x01
Success
> i2c_master_config 0x19
! Addr Clock  Flags Retries
# 0x19 100000 0x01  0

i2c_master_open

Abbreviation

i2cmo

Description

Open an I2C stream for read/write. Optionally specify the size of the read buffer.

The stream can then be used with the stream commands. Stream command behavior is modified for i2c as follows:

Stream CommandDescriptionSyntax
stream_readAdditional optional argumentsread <handle> <read size> [<flags> [<register address> [<slave address>]]]

For details, see I2C Read Command below
stream_writeAdditional optional argumentswrite <handle> <write size> [<flags> [<register address> [<slave address>]]]
For details, see I2C Write Command below
stream_closeCloses the stream.stream_close <handle>
stream_listList streams - i2c streams are identified with type I2Cstream_list

Notes:

Syntax

> i2c_master_open [<rx buffer>]

where:

I2C Write Command

Once an I2C stream is opened, the write command is used to write data to an I2C slave. The write command has additional arguments to specify the register address and slave address to write. write <handle> <write size> [<flags> [<register address> [<slave address>]]] where:

Notes:

I2C Read Command

Once an I2C stream is opened, the read command is used to read data from an I2C slave. The read command has additional arguments to specify the register address and slave address to read.

read <handle> <read size> [<flags> [<register address> [<slave address>]]] where:

Notes:

Supported Platforms

Example

The following shows how to read/write the LIS3DH Accelerometer via the I2C bus. The LIS3DH Accelerometer comes with the Seabass and Snapper evaluation boards).

Quick notes about the LIS3DH

Slave address = 0x19

If the MSb of a register address is set then the register address automatically increments for subsequent read/writes. This auto-increment is a feature of the LIS3DH, not of ZentriOS.

ZentriOS Command LogDescription

>i2c_master_config 0x19 standard 0 0x01
Success
> i2c_master_open
[Opened: 0]
0
> read 0 1 0 0x0F
33
> write 0 2 0x01 0xA0
aa
Success

> write 0 2 0x01
bb
Success
> write 0 2 0x01
cc
Success
> write 0 2
dd
Success
> read 0 4 0 0xA0
AABBCCDD


Configure I2C slave address: 0x19,
  'standard' clock, no retries, and hexify flag
Open an I2C stream


Read register 0x0F (aka Who Am I register)
  should return 0x33
Write CTRL_REG 1-4 (0x20 - 0x23),
  use LIS3DH's register auto-increment feature
  by setting MSb of register address.
  Use 'continued write' flag
Write CTRL_REG2 (0x21)
  (recall we're using 'continued write' flag
  and chip's register auto-increment feature)
Write CTRL_REG3 (0x22)


Write CTRL_REG4 (0x23). This is the last write
  so don't use the 'continued write' flag

Read back registers 0x20-0x23
  Set MSb of register address so the register address
  is automatically incremented

ls

Abbreviation

ls

Description

Return a list of available files located in internal, extended and bulk flash.

Use the -v (or equivalent -l) option for full details.

The -m, -b and -c support paging and limiting the output, for use when there are many files.

Syntax

> ls [-v/-l] [-m <i|e|b>] [-b <base sector>] [-c <max file count>]

where:

Properties

Supported Platforms

Example

Long listing, showing Type, Flags, and Handles (Hnd)

> ls -l
!  # Type  Flags  Hnd    Size       Version  Filename
#  0 e-FE   0041   54    7590       3.3.2.6  .recovery.html
#  1 e-FB   0001   85   44560       3.0.0.6  command_help.csv
#  2 e-FD   0001   62     135       3.0.0.6  default_setup.script
#  3 e-FE   0001   96    5430       3.3.2.6  favicon.ico.gz
#  4 e-03   0001   63    1216       3.0.0.6  geotrust_ca.pem
#  5 i-00   001B  170  327424       3.3.2.6  sys/kernel.bin
#  6 e-84   0005   52     820       3.2.0.0  sys/safemode.bin
#  7 i-81   001B    0  166096       3.3.2.6  sys/services.bin
#  8 e-01   0001    0  210412   5.26.230.12  sys/wifi_fw.bin
#  9 e-FE   0021   97     684       1.0.0.0  test1.html
# 10 e-FE   0001   53    1995       3.3.2.6  webapp/index.html
# 11 e-FE   0001   64    9530       3.3.2.6  webapp/unauthorized.html
# 12 e-FE   0001   56   22720       3.3.2.6  webapp/zentrios.css.gz
# 13 e-FE   0001   67   72947       3.3.2.6  webapp/zentrios.js.gz

Example

Listing showing extended memory files only, starting at file handle 56, count limited to 5 files:

> ls -l -m e -b 56 -c 5
!  # Type  Flags  Hnd    Size       Version  Filename
#  0 e-FE   0001   56   22720       3.3.2.6  webapp/zentrios.css.gz
#  1 e-FD   0001   62     135       3.0.0.6  default_setup.script
#  2 e-03   0001   63    1216       3.0.0.6  geotrust_ca.pem
#  3 e-FE   0001   64    9530       3.3.2.6  webapp/unauthorized.html
#  4 e-FE   0001   67   72947       3.3.2.6  webapp/zentrios.js.gz
>

load

Abbreviation

load

Description

Load a configuration from a file previously saved by the save command.

Syntax

> load [-v] <config_file>

where:

Supported Platforms

Example

> load config1.cfg
> Configuration successfully loaded

mdns_discover

Abbreviation

mdns

Description

Discover mDNS services on the local network. See variables mdns.enabled, mdns.interface, mdns.name, mdns.service, mdns.ttl

Syntax

> mdns_discover [-v] [<service type>]

where:

Supported Platforms

Example

> set wlan.ssid Zentri
Set OK
> set wlan.passkey secretkey
Set OK
> set mdns.enabled 1
Set OK
> mdns_discover
[Associating to Zentri]
Security type from probe: WPA2-AES
Obtaining IPv4 address via DHCP
IPv4 address: 10.5.6.115
Starting mDNS
mDNS domain: ZentriOS-102f1a.local
[Associated]
Services found: 4
Service: _csco-api._tcp.local
Name: _jenkins._tcp.local

Service: _https._tcp.local
Name: _workstation._tcp.local

Service: _http._tcp.local
Name: _http._tcp.local

Service: _csco-sb._tcp.local
Name: routera296b6._csco-api._tcp.local
Server: routera296b6._csco-api._tcp.local
Address: 10.5.6.1

network_down

Abbreviation

ndo

Description

Bring down a network interface. If provided, the network interface overrides the default specified by the variable network.default_interface. All open streams on the interface will be closed.

Syntax

> network_down [-i <wlan/softap>]

Supported Platforms

Example

> ndo
L000040
[2014-03-24 | 00:08:48: Disassociated]
R000009
Success

network_lookup

Abbreviation

nlo

Description

Perform a DNS lookup for a domain using the specified interface.

Syntax

> network_lookup [-i <wlan/eth/default>] <domain>

where:

Supported Platforms

Example

> nlo google.com
R000016
216.58.220.142

network_flush

Abbreviation

nfl

Description

Flush the DNS cache and/or flush the cached DHCP IP and forcibly renew the DHCP lease. DHCP caching depends on wlan.dhcp.cache_enabled.

If no arguments are supplied, the DNS cache is flushed, and the cached DHCP IP is cleared and the DHCP lease is forcibly renewed.

If the dns argument is supplied only the DNS cache is cleared.

If the dhcp argument is supplied the DHCP IP cache is cleared, and the DHCP lease is forcibly renewed.

Note: This command currently supports only the WLAN interface.

Syntax

> network_flush [ dns / dhcp ]

where:

To flush both DNS and DHCP caches, issue the command with no arguments.

Supported Platforms

Example

> nfl
R000009
Success

network_restart

Abbreviation

nre

Description

Restart the network. This command is equivalent to issuing the network_down command followed by the network_up command.

Note: This command is blocking. It does not return until the network has been brought up (or has failed to be brought up).

Syntax

> network_restart [-i <softap/wlan>]

where the -i option specifies the network interface to be restarted.

Supported Platforms

Example

The response shown is an example. Response varies depending on the network settings, time and date and other factors.

> nre
[2015-03-23 | 03:02:53: Disassociated]
[2015-03-23 | 03:02:53: Associating to Zentri]
Obtaining IPv4 address via DHCP
IPv4 address: 10.5.6.55
[2015-03-23 | 03:02:54: Associated]
Success

network_up

Abbreviation

nup

Description

Start the process to bring up a network interface.

The -s option prompts the user to select from a list of available APs and supply a passkey. If the -s option is used, ZentriOS automatically saves the credentials entered.

The -i option overrides the default network interface specified by network.default_interface.

NOTE! Every command that needs access to the network will automatically bring up the network interface. The network_up command is non-blocking (except when the -s option is used) and provided for convenience only.

See Procedure for Joining a WLAN Network.

Syntax

> network_up [<-s> / <-i [wlan]/[softap]>]

Supported Platforms

Example

> network_up -s
Scanning for networks...
! 3 networks found
!  # Ch RSSI MAC (BSSID)       Network (SSID)
#  0  6  -27 84:1B:5E:29:9D:F7 Take the blue pill
#  1 11  -68 EC:1A:59:36:5B:6C button_xt
#  2 11  -70 2C:B0:5D:31:6F:6A button

Type the number # that matches your Network: 0
Type the password for your Network         : welcome-to-kansas
[Associating to Take the blue pill]
In progress
[Associated]

network_verify

Abbreviation

nve

Description

Verify the module can connect to a Wi-Fi network with specific network credentials. This command provides a fast way test the network credentials entered by a user are valid when web setup with softAP is operational, see Configuration & Setup, Web Setup. At present, only the Wi-Fi credentials are verified. No attempt is made to verify whether the module can obtain an IP address using DHCP.

The network verify command can also be used to quickly test network credentials at any time, however if the module is already connected to a network on the wlan client interface, it will be automatically disconnected from that network first.

If the verification attempt is unsuccessful, the command responds with Timeout. Verification may be unsuccessful if either the credentials provided are incorrect, or the verification attempt takes longer than 1 second.

Notes

Syntax

> network_verify wifi <ssid> <bssid> <ap channel> [<security> <psk>] where:

Supported Platforms

Example (Open Security)

> network_verify wifi mynetwork 4C55CC102F1A 1
Success

Example (WEP40 Security)

> network_verify wifi mynetwork 4C55CC102F1A 1 1 1122334455
Success

Example (WPA/WPA2 Security)

> network_verify wifi mynetwork 4C55CC102F1A 1 4 1205089613366e362586ee5f9ac8f485188fb0bdab30f2f1c23295eb863122de
Success

ota

Abbreviation

ota

Description

Initiate a secure over-the-air update using the ota server specified by the dms.ota_host variable. The secure OTA protocol uses industry standard TLS/HTTPS security with both client-side and server-side certificate verification.

For details of this process and associated requirements, see Update and Recovery, Secure OTA Update. This process requires you to claim the device using the dms claim command.

As an additional measure of security, the server authenticates each device using the universally unique system.uuid embedded inside the hardware of each device.

Downloaded bundle files overwrite local files only if the bundle file has a later version. To ensure that bundle files overwrite local files regardless of version, force an update with the -f option.

Download a specific firmware bundle version with the -b option. Specifying a bundle forces an update. Bundle files overwrite local files regardless of version. See the note for the -b option in Syntax below.

To activate a module to receive custom firmware and files, use the -a option along with your activation code and password. All modules are activated and licensed for standard ZentriOS firmware, so when updating to standard firmware no activation code is required.

If you have firmware customised by Zentri for your application, or you would like Zentri to manage your host firmware or host application files on our secure servers, please contact Zentri to receive an activation code and password.

To maintain a saved configuration through an OTA update, save the configuration as default_config.csv. See save. See also Configuration and Setup, Default Variable Configuration.

See Networking and Security, TLS Errors for details of the error response to TLS failure.

Note: OTA requires a memory-intensive TLS connection, and may fail if memory is low. See Networking and Security, Increasing Available Memory for TLS.

To determine the result of the most recent ota command, see dms.ota_result.

Note: If the ota command fails with the message:

{"result":"fail","message":"device not claimed"}

then you need to claim the device before running the ota command. See Update and Recovery, the Zentri DMS Server.

The OTA sequence is as follows:

  1. An OTA request is invoked, via command or native API.
  2. The Device sends the OTA request to the Device Management Server (DMS).
  3. The DMS returns the OTA manifest response.
  4. ZentriOS compares its current product code (stored in manufacturing, or during a previous OTA) with the product code received in the OTA manifest response.
    IF the -x option was supplied, and the product codes are different, then the device first formats the extended flash before downloading the OTA files.
  5. The device downloads OTA files; only bundle files or files generated by the device are present on extended flash.
    Note: If the device does NOT have a valid product code, then a flash formatting will always happen during the first OTA after programming. (as the device does not have a valid product code).Also note the product code comes from the bundle version string. An example bundle string is:

Syntax

> ota [[ [-x] -b <bundle-version> / -f ] / -q ] [-u <user file>]

Properties

Supported Platforms

Example

> ota
Connecting to network
Request POST /ota/05b300df003134534e394b8330393232323a3533/0
Connecting (HTTP): ota.zentri.com:443
Starting TLS
HTTP response: 200
Downloading new firmware...
Bundle version: ZentriOS-1.0.0.1, Built:2015-11-11 02:23:15 for AMW004.3
Downloading: command_help.csv-1.0.0.1 (25822, 0xFB, 0x1)
Downloading: default_setup.script-1.0.0.1 (189, 0xFD, 0x9)
Downloading: /setup/index.html-1.0.0.1 (9266, 0xFE, 0x1)
Downloading: /setup/images.png-1.0.0.1 (18067, 0xFE, 0x1)
Downloading: /sys/kernel.bin-1.0.0.1 (352804, 0x0, 0x801F)
Downloading: wifi_fw.bin-1.0.0.1 (191677, 0x1, 0x8009)
Downloading: /sys/services.bin-1.0.0.1 (83848, 0x80, 0x801F)
Downloading: geotrust_ca.pem-1.0.0.1 (1162, 0x3, 0x9)
Downloading: /favicon.ico.gz-1.0.0.1 (1853, 0xFE, 0x1)
Downloading: /setup/index.css.gz-1.0.0.1 (10539, 0xFE, 0x1)
Downloading: /setup/index.js.gz-1.0.0.1 (38771, 0xFE, 0x1)
Updating kernel to version: 1.0.0.1
Updating firmware files...
Updating file: wifi_fw.bin to version: 1.0.0.1
Updating file: /sys/services.bin to version: 1.0.0.1
Found new bootable app: /sys/services.bin (47), booting to it now!
OTA completed successfully
[Ready]

ping

Abbreviation

ping

Description

Send one or more ICMP pings to an IP address or the network gateway using the -g option. If provided, the network interface overrides the default specified by the variable network.default_interface. Options must be provided in the order shown.

Syntax

> ping [-i <wlan/softap>] <[IP address]/[-g]> [# retries]

Supported Platforms

Example

> ping example.com 3
R000021
Ping reply in 183ms
R000021
Ping reply in 178ms
R000021
Ping reply in 177ms

pwm_update

Abbreviation

pwm

Description

Drive a GPIO with a pulse width modulated signal with duty_cycle in the range 0-100%. The PWM frequency has a module-dependent default and may be optionally set with the frequency option. Use the stop option to turn the PWM off.

See Peripherals, PWMs for frequency defaults and PWM groups for each module. GPIOs in the same PWM group cannot be used independently at the same time.

Syntax

> pwm <GPIO#> <duty_cycle / stop> [frequency] where:

Supported Platforms

Example

Set GPIO 10 to 30% duty cycle:

> pwm_update 10 30
R000009
Success

Blink LED wired to GPIO 21 at 50% duty cycle and frequency of 5Hz:

> pwm 21 50 5

Stop LED blinking - value remains high:

> pwm 21 stop

reboot

Abbreviation

reboot

Description

Reboot the application.

Note: the response displayed on reboot depends on the system.cmd.mode setting.

In human command mode, the response is similar to:

Rebooting
[2015-08-05 | 00:38:19: Disassociated]
ZentriOS-2.3.1.2, Built:2015-07-21 09:16:43 for AMW004.3, Board:AMW004-E03.3
[Ready]

There may be other messages depending on system settings.

In machine command mode, the response to the reboot command, followed by the reboot and a CR-LF sequence, is similar to:

R000079
ZentriOS-2.3.1.2, Built:2015-07-21 09:16:43 for AMW004.3, Board:AMW004-E03.3

Syntax

> reboot

Properties

Supported Platforms

Example

> reboot
Rebooting
[2015-08-05 | 00:38:19: Disassociated]
ZentriOS-2.3.1.2, Built:2015-07-21 09:16:43 for AMW004.3, Board:AMW004-E03.3
[Ready]

save

Abbreviation

save

Description

Save all ZentriOS variables to non-volatile flash memory.

If a file name is supplied, the saved configuration can be restored with the load command.

Save as default_config.csv to create a default settings file. If a file of this name is found, ZentriOS loads the configuration in default_config.csv after a successful OTA or if the factory reset GPIO is asserted for more than 5 seconds but less than 10 seconds. See:

If system.security_key is set, the file is automatically encrypted with that key, and the User Encrypted file flag is set. When ZentriOS reads files for internal use (within the MCU only), it automatically decrypts files encrypted with the system.security_key.

Note: During the save operation, interrupts are disabled. In particular, the UART rx interrupt may not be serviced during save. To ensure the save operation is completed, wait for the save command response before issuing further commands via the UART.

Syntax

> save [<config_file>]

where parameters are as follows:

OptionDescription
<config_file>Optional. Name of the configuration file to be saved

Properties

Supported Platforms

Example

> save
L000007
Saved
R000009
Success

Example 2

save config1.cfg
R000009
Success
ls
!  #   Size   Version  Filename
...
#  5   3868     1.0.0  config1.cfg
...

set

Abbreviation

set

Description

Set the value of a ZentriOS variable.

Syntax

> set <variable> <args>

Note: The set command displays the Too many args error only if the number of space-separated arguments exceeds the maximum for all variables (5). However the number of arguments for the set command depends on the variable being set, and the form in which the variable is specified: abbreviations for variables vary from one to three arguments in length, and variable settings may require one or two arguments. If you specify too many arguments when setting a specific variable, surplus arguments are ignored. Refer to the variable documentation for the number of arguments for a specific variable.

Properties

Supported Platforms

Example

> set wlan.ssid "My Home Network"
R000008
Set OK

setup

Abbreviation

setup

Description

The setup command simplifies the process of connecting a ZentriOS device to a Wi-Fi network.

It can be run automatically on boot or in response to asserting a GPIO. It also allows for setup from the ZentriOS terminal.

The setup command allows for setting up network credentials via a web browser. See Configuration and Setup, Setup with a Web Browser.

The setup command can also be used to automate device configuration and setup with a configuration script.

See:

Syntax

> setup <web/status/stop/cmd [-v] [<script_file>]>

OptionDescription
webWhen called with the web option, setup starts a Wi-Fi Access Point and a web server, the Wi-Fi AP credentials are configured using the variables setup.web.ssid and setup.web.passkey. Once connected to the ZentriOS Setup AP, a Wi-Fi client uses a web browser to setup ZentriOS variables and connect to your local Wi-Fi network. Web setup is non-blocking. The root of the web app is configured with the setup.web.root_filename variable.
statusThe status option allows an MCU host to determine whether setup is in-progress. Response is 1 if setup is in progress, otherwise 0.
stopThe stop option terminates any in-progress setup activity.
cmdWhen called with the cmd option, setup runs the script default_setup.script located on the filesystem, or alternatively the optional configuration script specified by <script_file>. The setup command blocks until completion when used with the cmd option.
-vExecute script verbosely, displaying all script comments, commands and output. The default_setup.script is always executed verbosely.
<script_file>Default when omitted: default_setup.script The setup script can be used to run ZentriOS commands in sequence. See Configuration and Setup, Configuration Script.

Supported Platforms

Example

Setup via Soft AP and Web App

> setup web
In progress
Rebooting
ZENTRI-AMW007-1.0.0.4, 2016-08-18T05:32:24Z, ZentriOS-WL-1.0.0.4, Board:AMW007-E03.2

While In progress is displayed, connect a computer or mobile device to Soft AP, enter password (default password), in web browser go to web setup DNS (default setup.com), choose network from scan list and enter network password.

Setup up with cmd option

> setup cmd
> Scan and select a network:
network_up -s
Scanning for networks...
! 4 networks found
! # Ch RSSI MAC (BSSID)       Network (SSID)
# 0 06  -35 84:1B:5E:29:9D:F7 GameOverMan
# 1 06  -88 28:C6:8E:70:93:18 Philips Home Network_EXT
# 2 11  -65 EC:1A:59:36:5B:6C laboite_xt
# 3 11  -73 2C:B0:5D:31:6F:6A laboite

Type the number # that matches your Network: 0
Type the password for your Network         : pullyourselftogetherhicks
[Associating to GameOverMan]
In progress
> Enabling network auto-join
set wlan.auto_join.enabled true
Set OK
> Saving settings
save
Saved
Success
> Security type from probe: WPA2-Mixed
Obtaining IPv4 address via DHCP
IPv4 address: 192.168.0.32
[Associated]
> Exiting Cmd Setup Mode

sleep

Abbreviation

sleep

Description

Put the application into a low-power sleep state. The application sleeps until the wakeup timeout (system.wakeup.timeout) expires or a wakeup event (system.wakeup.events) occurs.

Syntax

> sleep

Supported Platforms

Example

> set system.wakeup.events uart0|gpio5
Set OK
> set system.wakeup.timeout 10
Set OK
> sleep

... wait 10 seconds ...

ZentriOS-1.1.1.0, Built:2014-04-02 02:23:15 for AMW004.3, Board:AMW004.3-E03.1

smtp_send

Abbreviation

smtp

Description

Send email to a specified email address. See SMTP variables:

Syntax

> smtp <to address> <subject> <content length>
[<content length> bytes of data ...]

where:

Immediately after issuing the command, <content length> characters of data should be sent. This is the body of the email.

Note that most SMTP servers require SSL/TLS encryption. Some servers, including gmail, use additional authentication methods like OAUTH by default. These additional authentication methods are not supported and may need to be disabled server-side.

Supported Platforms

Example

> smtp_send first.last@youremail.com "World greetings" 5
Hello
[Associating to MY_NETWORK]
Security type from probe: WPA2-AES
Obtaining IPv4 address via DHCP
IPv4 address: 10.5.6.59
[Associated]
Success

softap_get_rssi

Abbreviation

srssi

Description

Get the received signal level (RSSI, in dBm) of a SoftAP client. The value is averaged to improve accuracy by setting the variable softap.rssi_average

Syntax

> softap_get_rssi <client MAC>

where:

Example

> srssi 11:22:33:44:55:66
R000005
-47

spi_master_config

Abbreviation

spimc

Supported Platforms

Description

Configure a SPI slave peripheral such as an accelerometer, humidity sensor, light sensor, etc.

Note: This is a run-time only command. The settings are reset upon a reboot/power-cycle.

This should be issued before using the spi_master_open command to open a SPI stream.

To display the SPI configuration for a previously configured slave-select GPIO, issue the command with only the <slave-select gpio #> argument.

Syntax

> spi_master_config <slave-select gpio #> <config bitmask> [<clock rate>]

where:

<config bitmask> is a bitmask specifying the various flags for the SPI slave. The bits have the following meanings:

Bit #NameDescription
0Clock Edge
  • 0 : shift data out on falling-edge, shift data in on rising-edge
  • 1 : shift data out on rising-edge, shift data in on falling-edge
1Clock Idle Level
  • 0 : clock idles low
  • 1 : clock idles high
2Data Bit Order
  • 0 : data bytes are shifted out Least-Significant Bit first (LSb)
  • 1 : data is shifted out Most-Significant first (MSb)
Note: Only MSb first is supported for the AMW004 module.
3Read-After-WriteWhen this is specified, when data is written to the SPI slave, the simultaneously read data is buffered.
If this flag is not specified, when data is written, the read data is dropped.
4Keep Slave Select Signal AssertedSometimes it is necessary to keep the slave-select asserted between reads/writes.
If this flag is not specified, the slave-select is de-asserted after a read/write command.
When this flag is specified, after a slave-select is asserted for a read/write command, it remains asserted until one of the events occurs:
  • close command is issued for the stream
  • A different &lt;slave-select gpio #&gt; is specified as an argument to a read/write command
  • 0 bytes written to stream (i.e. write <handle> 0)
5HexifyWhen set, input data to the write command is converted from a hex string to binary.
Output data from the read command is converted from binary to a hex string.
NOTE: When this flag is set, up to <rx buffer>/2 -1 bytes may be read at a time

Supported Platforms

Example

> spi_master_config 9 0C
Success
> spimc 9
!  # Flags Clock
#  9 0x0C  2000000
> get gp u
!  # Description
...
#  9 SPI0 CS
...

spi_master_open

Abbreviation

spimo

Description

Open a SPI master stream for read/write. Optionally specify an Rx buffer size.

The stream can then be used with the stream commands. Stream command behavior is modified for SPI as follows:

Stream CommandDescriptionSyntax
stream_readAdditional optional argument specifies SPI slave selectread <handle> <read size> [<slave-select gpio #>]
stream_writeAdditional optional argument specifies SPI slave selectwrite <handle> <write size> [<slave-select gpio #>]
stream_pollPoll for SPI Rx datapoll <handle>
returns 1 if <rx buffer> contains data, else 0.
stream_closeDe-asserts the current slave-select and closes the stream.stream_close <handle>
stream_listList streams - SPI streams are identified with type SPIstream_list

Before using spi_master_open command, the <slave-select gpio #> must have been previously configured using the spi_master_config command. If no argument is supplied, the most recently specified <slave-select gpio #> is used.

Note: The caller must ensure that the contents of <rx buffer> is cleared before switching <slave-select gpio #>, as data is always read from <rx buffer> before reading from the SPI bus.

See Networking and Security, Network Connections and Streams.

Syntax

> spi_master_open [<rx buffer>]

where:

Supported Platforms

Example

ZentriOS Command LogDescription

> spi_master_open 256
0
> write 0 10 2
...
> read 0 10

open the SPI master stream with <rx buffer> size of 256 bytes
(return stream handle 0)
write 10 bytes to slave 2 as the slave select to SPI bus
(this simultaneously reads 10 bytes)
read 10 bytes from buffer

stream_close

Abbreviation

close

Description

Close an open network or file stream specified by [handle], or alternatively close all open streams.

See Networking and Security, Network Connections and Streams.

Syntax

> stream_close <[handle]/[all]>

Supported Platforms

Example

> close all
[2014-04-02 | 13:32:04: Disconnected: 0]
[2014-04-02 | 13:32:04: Disconnected: 1]
Success

stream_list

Abbreviation

list

Description

Return a list of open streams.

See Networking and Security, Network Connections and Streams.

Syntax

> stream_list

Supported Platforms

Example

> list
!# Type  Info
#0 TCPC  google.com:80 (32288)
#1 HTTP  example.com:80 (37289)

stream_poll

Abbreviation

poll

Description

Poll a stream to check if data is available. Returns 0 if open with no data to read, 1 if data is available and 2 if the stream has been closed remotely. Use the all option to return the status of all open streams. To avoid polling, use a GPIO (may be assigned when the stream is opened) as an interrupt line to the host.

Determine the number of RX or TX bytes that can be buffered with the -r or -t arguments.

If bus.command.write_check_enabled is set, when writing to a network stream, ZentriOS checks the size of the write (TX) buffer, to ensure that a full stream_write can be completed.

Syntax

> stream_poll [all] <handle> [[-r][t]]

where:

If -r and/or -t argument is included in the command, the response format is as follows:

Poll specific connection

> poll 0 -r
<status>,<Rx bytes available>
> poll 0 -t
<status>,<Tx bytes available>
> poll 0 -rt
<status>,<Rx bytes available>,<Tx bytes available>

Poll all connections

> poll all -r
<handle>,<status>,<Rx bytes available>|<handle>,<status>,<Rx bytes available>|...
> poll all -t
<handle>,<status>,<Tx bytes available>|<handle>,<status>,<Tx bytes available>|...
> poll all -rt
<handle>,<status>,<Rx bytes available>,<Tx bytes available>|<handle>,<status>,<Rx bytes available>,<Tx bytes available>|...

where:

Supported Platforms

Example

> poll 0
1
> read 0 100
hello!
> poll 0
0
> poll all
0,0|2,1|3,1

stream_read

Abbreviation

read

Description

Read up to <size> bytes from a network or file stream specified by <handle>. Returns data immediately (if available), does not wait to receive data.

To check for data, use the stream_poll command or the GPIO (assigned when the stream was opened) as an interrupt line to the host.

For file streams, the file is automatically closed if the end of file is reached.

Read times out after the period specified in bus.command_read_timeout.

Data Size Returned by stream_read

For network streams, ZentriOS may buffer up to seven packets with each packet containing up to 1460 (MTU) data bytes. To avoid receiving data fragmented across packets, <size> should be set to 1460 bytes.

The number of bytes returned in the response to the stream_read command is determined as follows:

bytes_returned = MIN(Max packet size, <size arg>, poll -r)

i.e. the number of bytes returned is the minimum of:

See Networking and Security, Network Connections and Streams.

Syntax

> stream_read <handle> <size>

where

Supported Platforms

Example

> read 0 200
R000202
<!doctype html><html itemscope="" itemtype="http://schema.org/WebPage"
 lang="en-AU"><head><meta content="/images/google_favicon_128.png"
itemprop="image"><title>Google</title><script>(function(){
wind

stream_write

Abbreviation

write

Description

Write data to a network or file stream. As described in Serial Interface, Command Protocol, the command must be terminated by \r\n.

If no option is specified, ZentriOS waits for <size> number of data bytes then immediately sends the data to the stream before returning a response.

If the -f (flush) option is specified, then the written data is buffered to the maximum packet size before being automatically flushed to the remote side. The -f option can be used for the following stream types:

For TCP and TLS streams, the maximum packet size is an MTU (1460 bytes).

For WebSocket client/server streams, data is not locally buffered, however 'continuation' frames are used. When the -f option is specified, each written data chunk is sent as a continuation frame. If -f is not specified, then the 'final frame' flag is set.

Use the -c option to enable automatic continuation frames for large writes to WebSocket client/server streams.

For WebSocket client/server streams, you can use the -p option to send a WebSocket ping frame as a keepalive.

Write times out after the period specified in bus.command.write_timeout.

See Networking and Security, Network Connections and Streams.

If bus.command.write_check_enabled is set, when writing to a network stream, ZentriOS checks the size of the write (TX) buffer, to ensure that a full stream_write can be completed.

Syntax

> stream_write <handle> <size> [-p] [-f] [-c]

where:

Supported Platforms

Example

> write 3 10
Success

tcp_client

Abbreviation

tcpc

Description

Open a TCP stream to a remote server at the specified network location.

Timeout is determined by tcp.client.connect_timeout.

See Networking and Security, Network Connections and Streams.

Syntax

> tcp_client [-i <wlan/softap>] [-l <local port>] [-g GPIO#] <host> <port>

where:

Options must be provided in the order shown.

Supported Platforms

Example

> tcpc google.com 80
L000028
Resolving host: google.com
L000052
[2014-03-24 | 01:07:12: Connecting: google.com:80]
L000036
Connecting (TCP): 74.125.237.96:80
L000039
[2014-03-24 | 01:07:12: Connected: 0]
R000003
0

tcp_server

Abbreviation

tcps

Description

Start/stop a TCP server specified by the variables tcp.server.*. If provided, the network interface and port override defaults specified by the variables network.default_interface and tcp.server.port respectively.

Syntax

> tcp_server [-i <wlan/softap>] <start/stop> [port]

where:

Options must be provided in the order shown.

See Networking and Security, Network Connections and Streams.

Supported Platforms

Example

> tcps start
L000036
TCP server listening on port: 3000
R000009
Success

tls_client

Abbreviation

tlsc

Description

Open a secure TCP stream to a remote server with the specified properties.

Timeout is determined by tcp.client.connect_timeout.

See Networking and Security, TLS Errors for details of the error response to TLS failure.

See Networking and Security, Network Connections and Streams.

Syntax

> tls_client [-i <wlan/softap>] [-l <local_port>] [-g GPIO#] <host> <port> [ca_cert_filename]

where:

Supported Platforms

Example

> tlsc www.google.com 443
L000032
Resolving host: www.google.com
L000057
[2014-03-24 | 01:15:53: Connecting: www.google.com:443]
L000038
Connecting (TLS): 74.125.237.211:443
L000039
[2014-03-24 | 01:15:55: Connected: 1]
R000003
1

tls_server

Abbreviation

tlss

Description

Start/stop a TLS server on the specified port.

If starting the server and no port is specified, the default is the port specified by tcp_server_port.

The server certificates must be pre-configured. See Networking and Security, TLS Server.

See Networking and Security, Network Connections and Streams.

Syntax

tls_server <start/stop> [port]

Supported Platforms

Example

> tlss start 5000

uart_update

Abbreviation

uartu

Description

Update the UART to the current UART variable settings without rebooting the device.

For this command to have an effect, the values of one or more of the uart variables must first be changed:

Syntax

> uart_update <uart#>

Supported Platforms

Example

> uart_update 0
Success

udp_client

Abbreviation

udpc

Description

Open a UDP stream to a remote server at the network location <host>:<port>. If provided, the network interface overrides the default specified by the variable network.default_interface.

The option -g GPIO# specifies which GPIO indicates buffered data is waiting to be read. See also system.oob.gpio.

The [local port] may also be provided if desired. Options must be provided in the order shown.

Issuing the command udp_client 255.255.255.255 results in broadcast to the local network.

See Networking and Security, Network Connections and Streams.

Syntax

> udp_client [-i wlan/softap] [-g GPIO#] <host> <remote port> [local port]

Supported Platforms

Example

> udpc 192.168.45.67 3000
L000057
[2014-03-24 | 01:16:40: Connecting: 192.168.45.67:3000]
L000031
Resolving host: 192.168.45.67
L000032
Connecting: 192.168.45.67:3000
L000039
[2014-03-24 | 01:16:40: Connected: 2]
R000003
2

udp_server

Abbreviation

udps

Description

Start and stop the UDP server.

When the UDP server is started the read and write sub-commands are available.

When the UDP server is started, it is assigned a stream handle, indicated in the ZentriOS response by Opened: <stream>.

This allows for the equivalent stream read and write commands.

The read command is functionally the same as udps read.

The write command is functionally the same as udps write without the <address> and <port> options. The write command writes to the single UDP server stream, and consequently writes to all clients connected to the UDP server.

See:

Syntax

start, stop

> udp_server <start/stop> [port] Start and stop the UDP server. Port may be optionally specified. If no port is specified the default is udp.server.port.

read

> udp_server read [-q] [<byte_count>] where :

write

> udp_server write <byte_count> [<address> <port>] where :

Supported Platforms

Example

> udp_server start 5000
[2014-11-28 | 07:14:49: Opened: 0]
0
UDP server listening on port: 5000
> read 0 100
Hello server
> udp_server write 12
Hello client
Success
> udp_server read -q 100
10.5.6.60,52333,Hello again server
> write 0 18
Hello again client
Success
> udps stop
[2014-11-28 | 07:15:31: Closed: 0]
UDP server stopped
Success

version

Abbreviation

ver

Description

Returns the ZentriOS firmware bundle version. This is a convenience command that is equivalent to reading the system.version variable.

Syntax

version

Properties

Supported Platforms

Example

> ver
R000069
ZentriOS-W-3.0.0.0, Built:Dec 09 2015 for AMW004.3-E03.1

websocket_client

Abbreviation

webc

Description

Opens a client websocket stream to a remote server. Returns a stream handle which may then be used with the read/write/poll/close commands.

The Websocket client connection can be controlled by a GPIO. See the ioconn.protocol web.

Data availability can be determined by an OOB GPIO event. See the system.oob.gpio event websocket.client.data_gpio.

See Networking and Security, Websocket Client.

Websocket Message Format

Websocket data passed between ZentriOS and remote server is sent in messages or frames. These messages start with a header. One element of the header is the message type. ZentriOS supports the 'text' and 'binary' message types. Note that ZentriOS treats all data as binary. The message type is only used by the remote side (for instance so a javascript library can convert the data to the correct format).

For more information see: https://developer.mozilla.org/en-US/docs/WebSockets/Writing_WebSocket_servers

Syntax

> websocket_client [-i <wlan/softap>] [-g <gpio> ] [-f <txt/bin>] <url> [<cert filename>] where:

Supported Platforms

Example

> websocket_client ws://mywsserver.com
0

wlan_get_rssi

Abbreviation

rssi

Description

Get the received signal level (RSSI, in dBm) of the Access Point the wlan interface is connected to. The value is averaged to improve accuracy by setting the variable wlan.rssi_average.

Syntax

> wlan_get_rssi

Supported Platforms

Example

> rssi
R000005
-47

wlan_scan

Abbreviation

scan

Description

Initiate a Wi-Fi scan and return results; optionally specify a channel and AP SSID to scan for. For verbose scans, -v must be the first argument. Information returned by scan results is described in the following table.

NameDescription
ChThe WLAN radio channel the AP is operating on
RSSISignal strength of the AP in units of dBm
BSSIDMAC address of the AP
RateThe maximum data rate supported by the AP in kilobits/s
e.g. 54000 = 54Mbit/s
SecuritySecurity type used by the AP e.g. Open, WPA2-AES, etc.
ModeAP mode. Inf = Infrastructure, Ad = Ad-hoc
LenNumber of characters in the SSID
SSIDAP name. APs with a hidden SSID are displayed as

Verbose scans return all columns of data. Non-verbose scans return only columns:# Ch RSSI MAC (BSSID) Network (SSID)

Syntax

> wlan_scan [-v] [<channel-spec> [ssid]] where:

Supported Platforms

Example

> scan -v
R000196
! 2 found
! # Ch RSSI BSSID              Rate Security Mode Len SSID
# 0 01  -24 EC:1A:59:36:5B:6C 144.4 Open      Inf  13 Ch1_Nearby_AP
# 1 06  -85 84:1B:5E:29:9D:F7 450.0 WPA2-AES   Ad  14 Ch6_Distant_AP

wps

Abbreviation

wps

Description

WPS is currently disabled. If you require WPS support, please contact Zentri.